K11 Owners Group

Acording to Clymer manual. It lists in Table 11.
front brake caliper mounting bolts
Outer 2 bolts 5-10 Nm
Inner 2 bolts 25-35 Nm
Im not sure if this helps.

Brilliant, thanks very much Very Happy

I have had to strip a front brembo caliper and fit new seals and pistons, does anyone know the correct torque for the 4 bolts that hold the two halves together, I have currently done them up to 15nm
...

She was last mot'd 22/04/09 with 73018 miles

Today she sailed through with compliments from tester and 73195 miles Very Happy

http://i36.photobucket.com/albums/e43/waynedear155/Mobile%20Uploads/2017-05/ ...

Finished with an abs reset and put back bodywork, now she is ready Very Happy

http://i36.photobucket.com/albums/e43/waynedear155/Mobile%20Uploads/2017-05/9FB5BAD0-EAFD-48DF-8D73-8E5EE349DB07_zpstfcm7tdr.jp ...

Now 2000 mile later a silver on the welsh Nat road rally and a start to the Round Britain ( Photo ) rally.
thanks for the help john

Congratulations

I picked up one that had been standing for ...

New master cylinder repair kit fitted, bled perfectly Very Happy

Went for a spin on a dirty alley, no one told me you had to reset the abs Shocked

Learnt how, be done tomorrow

Would anyone have a clue what make the alarm is on my K, all I have to go on is the fob Sad

http://i36.photobucket.com/albums/e43/waynedear155/Mobile%20Uploads/2017-05/06B2704B-A3A7-4F60-85B3-C27D7FE ...

Also, I pressurise the system by clamping the lever overnight. This compresses all the remaining air bubbles and helps them to float to the highest part of the system, hopefully the reservoir. When yo ...

Pair of wheels in reasonable condition, Metz front Conti rear, abs side disc is cracked.

£100 delivered, (UK normal postcodes only, I will post anywhere but would need to get a price)

http://i3 ...

I have always found that when bleeding and cannot get rid of all the bubbles I wind a type of tape around the threaded part of the bleed nipple, the sort used by plumbers to seal compression joints. ...

How are you bleeding it? I used a mighty vac to suck at the nipple and gently squeezed and released the lever. Make sure the lines are tight, and make sure you keep the tiny meter cylinder full. It's ...

I know your pain, £65 for the K, £20 for a used one for the car 2nd hand.

I have just replaced the front lines with stainless and rebuilt the back.
The abs for the back bled perfectly as did the caliper.
Now onto the front, bled at the abs pump until fluid ran clear BUT I ...

looking at the threads of your plug on the right, it appears that the threads look a bit rounded. Did it come out easy?

Some have taken the oil filter wrench and drilled 2-3 self tapping sheet met ...

Today I started the much needed service of the Lt., it has been stood for 3 years, warmed engine, drainded oil, removed oil filter plate to remove filter
Shocked

It will NOT move, I ...

Something some have used, tape off the Red area, then use some spray-on truck bed liner or spray on undercoating.
Give some decent protection and resists rock chips.

Thanks Scott, I have ordered s ...

The white stuff is annoying me, does anyone have the black cover piece please Very Happy

http://i36.photobucket.com/albums/e43/waynedear155/Mobile%20Uploads/2017-04/8B979527-3863-4DC4-AC03-E14500D916B0 ...

I like that, looks purposeful Cool

Battery and service kit ordered.
Went to do a bit of Fettling today and found a crack in the front disk Sad

Good luck, wish I had accepted fusion when offered.. Crying or Very sad